不同环境因素对引压管腔动态特性影响

为了探索引压管腔在动态压力校准和使用中不同环境因素对动态特性的影响,推导了管腔传压模型和谐振频率关系式,确立了影响管腔动态特性的参数,包括静态压力、温度、气体介质等。采用引压管腔专用实验装置进行了不同环境参数状态的实验验证,结果表明:静态压力仅会影响管腔在谐振频率附近的输出,随着静态压力的增大而非线性增大,对动态特性并无明显改变;温度会改变管腔的谐振频率和动态特性,随着温度的升高,谐振频率增大但输出幅值随之减小;气体介质的不同会彻底改变管腔动态特性,主要取决于介质的声速。该研究为引压管腔在使用环境下数据的评价和数据修正上提供了一定参考依据。     

A novel approach for predicting inlet pressure of aircraft hydraulic pumps under transient conditions

Cavitation caused by insufficient suction is a major factor that influences the life of aircraft pumps. Currently, pressurizing the tank can solve the cavitation problem under steady large-flow conditions. However, this method is not always effective under transient conditions (from zero flow to full flow in a very short time). Moreover, to apply and design other measures, such as a boost impeller, the suction dynamics during the transient period must be investigated. In this paper, a novel approach based on the pressure wave propagation theory is proposed for predicting the inlet pressure of an aircraft pump under transient conditions. First, a dynamic model of a typical aircraft pump is established in the form of differential equations. Then, the transient flow model of the inlet line is described using momentum and continuity equations, and the governing equations are discretized by the method of characteristics and the finite difference method. The simulated results are in good agreement with the results from verification tests. Further simulation analysis indicates that the wave velocity and transient time may influence the inlet and reservoir pressure as well as the size of the inlet line. Finally, solutions for upgrading the inlet pressure are discussed. These solutions provide guidelines for designing inlet installations.     

Effects of yaw-roll coupling ratio on lateral-directional aerodynamic characteristics

Experimental investigation of large amplitude yaw-roll coupled oscillations was conducted in a low-speed wind tunnel using an aircraft configuration model. A special test rig was designed and constructed to provide different coupled motions from low to high angles of attack.A parameter ‘‘coupling ratio" was introduced to indicate the extent of yaw-roll coupling. At each pitch angle, seven coupling ratios were designed to study the yaw-roll coupling effects on the lateraldirectional aerodynamic characteristics systematically. At high angles of attack, the damping characteristics of yawing and rolling moments drastically varied with coupling ratios. In the coupled motions with the rotation taking place about the wind axis, the lateral-directional aerodynamic moments exhibited unsteady characteristics and were different from the ‘‘quasi-steady" results of the rotary balance tests. The calculated results of the traditional aerodynamic derivative method were also compared with the experimental data. At low and very high angles of attack, the aerodynamic derivative method was applicative. However, within a wide range of angles of attack, the calculated results of aerodynamic derivative method were inconsistent with the experimental data, due to the drastic changes of damping characteristics of lateral-directional aerodynamic moments with yaw-roll coupling ratios.     

交流伺服系统特性分析与测试

分析了交流伺服系统的基本原理和电气性能特点。介绍了交流伺服系统主要性能评价指标和测试方法。据此,根据GB/T 16439—2009《交流伺服系统通用技术条件》中交流伺服系统试验测试的要求和特点,设计和搭建了用于交流伺服系统测试用的平台,并且介绍了在该平台实现交流伺服系统性能试验的方法。测试系统的设计实现为类似试验站的研制提供了重要参考。     

锥形间隙孔型阻尼密封动力特性分析及抑振机理

应用非定常动网格技术建立了锥形间隙孔型阻尼密封动力特性多频椭圆涡动求解模型,研究了锥形度和涡动频率对孔型阻尼密封泄漏特性与动力特性的影响,分析了锥形间隙孔型阻尼密封的抑振机理。结果表明:锥形间隙增强了孔型阻尼密封的泄漏直通效应,增加了密封泄漏量。在平均间隙相等的情况下,收敛间隙孔型阻尼密封泄漏量小于发散间隙孔型阻尼密封;在同一涡动频率下,刚度系数随着锥形度的增加而增大,阻尼系数随着锥形度的增加而减小;收敛间隙孔型阻尼密封具有较大的正直接刚度,增加了转子系统的固有频率,发散间隙孔型阻尼密封产生较大的负直接刚度;收敛间隙孔型阻尼密封具有较大的有效刚度和穿越频率,较小的有效阻尼,发散间隙孔型阻尼密封具有较大的有效阻尼,较小的有效刚度和穿越频率;在锥形间隙孔型阻尼密封结构设计时,需要同时考虑转子系统固有频率和同心度的影响。      

EXPERIMENTAL INVESTIGATION ABOUT THE UNSTEADY AERODYNAMIC CHARACTERISTICS OF WINGS

ＥＸＰＥＲＩＭＥＮＴＡＬＩＮＶＥＳＴＩＧＡＴＩＯＮＡＢＯＵＴＴＨＥＵＮＳＴＥＡＤＹＡＥＲＯＤＹＮＡＭＩＣＣＨＡＲＡＣＴＥＲＩＳＴＩＣＳＯＦＷＩＮＧＳＹｕＸｉｎｚｈｉ；ＹａｎｇＹｏｎｇｎｉａｎ；ＷｕＺｅ（Ａｉｒｃｒａ．ｆｔＥｎｇｉｎｅｅｒｉｎｇＤｅｐａ...     

质量师系统与型号研制RMSS方案论证

阐述了型号质量师系统参与型号研制方案论证的必要性,着重探讨了型号质量师参与型号可靠性、维修性、安全性和保障性(RMSS)方案工作的内容和要求,以及做好方案论证工作,对建立型号研制RMSS监控的指导意义。     

塞式喷管效率高度特性分析

通过理论分析,结合塞式喷管具有高度补偿特性的特点,根据气流流动的情况,将塞式喷管的推力分为两部分,建立了两个不同的塞锥表面压力分布的数学模型,来分析塞式喷管发动机效率的高度特性非单调性变化的规律以及塞锥表面压力分布对其的影响。结果表明,在高的环境压强下工作时,由塞式喷管的高度补偿能力所获得的推力是引起效率高度特性曲线非单调变化的原因;在低的环境压强下工作时,由于塞锥的截短,效率高度特性曲线在设计点之前达到最大值。      

用于喷气客机概念设计的气动特性分析程序

针对喷气客机概念设计需求,在确定了升阻特性的估算方法后,应用MATLAB开发气动特性分析程序。以典型喷气客机为例,验证了气动分析模型和计算程序的精度。所开发气动特性估算程序能快速对喷气客机初步方案气动特性进行评估。设计人员只需通过用户界面给出飞机外形参数和飞行条件,就可快速获得巡航构型曲线、升阻比曲线、巡航效率曲线、抖振边界曲线,以及起降构型升力线和升阻比曲线。     

高速圆柱滚子轴承动态特性分析

建立了高速圆柱滚子轴承非线性动力学分析数学模型,并采用Newton-Raphson法对该模型进行求解,得到滚子轴承动态性能参数;分析了轴承在不同径向载荷作用下,不同角位置处滚子自转速度变化规律,得出滚子与套圈滚道间最小油膜厚度和接触载荷的分布情况.结果表明:轴承在转速一定时,随着径向载荷的增大,受载滚子数增多;较小的径...